Difference between revisions of "Installing FusionPBX behind pfSense"
From FusionPBX
(→3. Configure FusionPBX) |
|||
| (2 intermediate revisions by the same user not shown) | |||
| Line 50: | Line 50: | ||
'''System >> Variables''' | '''System >> Variables''' | ||
| − | '''IP Address''' | + | '''IP Address Section''' |
| + | If you have a static public IP you can replace XX.XX.XX.XX with that IP. | ||
| − | external_rtp_ip | + | external_rtp_ip XX.XX.XX.XX |
| − | external_sip_ip | + | external_sip_ip XX.XX.XX.XX |
| + | |||
| + | or if you have a dynamic IP address you can get a Dynamic DNS from a company such as dyndns.org. | ||
| + | |||
| + | external_rtp_ip myname.dyndns.org | ||
| + | external_sip_ip myname.dyndns.org | ||
'''Advanced >> SIP Profiles''' | '''Advanced >> SIP Profiles''' | ||
| Line 62: | Line 68: | ||
'''Value:''' true | '''Value:''' true | ||
'''Enabled:''' True | '''Enabled:''' True | ||
| + | |||
| + | Now we need to Stop and Start the internal profile for the changes to take effect. | ||
| + | |||
| + | '''Status >> SIP Status''' | ||
| + | |||
| + | Stop and Start the Internal Profile. | ||
In most cases this should work fine. | In most cases this should work fine. | ||
I have tested with inbound and outbound calls, calls between extensions, music on hold, call transfers without issues. | I have tested with inbound and outbound calls, calls between extensions, music on hold, call transfers without issues. | ||
Latest revision as of 22:48, 2 April 2014
The principles explained here can also apply to almost any other Firewall.
1. Create Alias Ports in pfSense
- First we need to config pfSense to open the necessary ports for FusionPBX and Freeswitch
- In pfSense navigate to Firewall >> Aliases and click on the Ports TAB.
Name: PBX Description: FusionPBX Type: Ports
- Then proceed to add the ports as follows:
Port Description 80 HTTP 443 HTTPS 5060:5061 SIP Internal 5080:5081 SIP External 16384:32768 RTP
- After you are finished Click SAVE
2. Configure pfSense Port Forwarding
Click on the '+' to add a new Entry
Firewall >> NAT >> Port Forward: Edit
Interface: WAN
Protocol: TCP/UDP
Destination: <<Select a Public IP from the List>>
Destination Port Range:
from: (Other) PBX
to: (Other) PBX
Redirect target IP: 10.10.0.10 Redirect target port: (Other) PBX
Description: FusionPBX NAT reflection: Use system default
- Click SAVE when done.
3. Configure FusionPBX
- In FusionPBX
System >> Variables
IP Address Section If you have a static public IP you can replace XX.XX.XX.XX with that IP.
external_rtp_ip XX.XX.XX.XX external_sip_ip XX.XX.XX.XX
or if you have a dynamic IP address you can get a Dynamic DNS from a company such as dyndns.org.
external_rtp_ip myname.dyndns.org external_sip_ip myname.dyndns.org
Advanced >> SIP Profiles
Edit the Internal Profile and add:
Name: aggressive-nat-detection Value: true Enabled: True
Now we need to Stop and Start the internal profile for the changes to take effect.
Status >> SIP Status
Stop and Start the Internal Profile.
In most cases this should work fine. I have tested with inbound and outbound calls, calls between extensions, music on hold, call transfers without issues.
